Graco 334014A Manuel d'utilisateur

OperationHusky ™ 1050HP 2:1Air-OperatedDiaphragm Pump334014AEN1–inch high-pressure pump with modular air valve for fluid transfer applications. For pro

InstallationAir Exhaust VentilationThe air exhaust port is 3/4 npt(f). Do not restrict theair exhaust port. Excessive exhaust restriction cancause err

InstallationFluid Supply LineSee Typical Floor Mount Installation, page 121. Use grounded flexible, fluid supply hoses (G).See Grounding, page 8 .2. If

InstallationTypical Floor Mount InstallationFigure3 Typical floor mount installationKEYA Air supply line JFluid drain valve (required)BBleed-type maste

OperationOperationPressure Relief ProcedureFollow the Pressure Relief Procedurewhenever yousee this symbol.This equipment stays pressurized until pres

OperationStart and Adjust the Pump1. Be sure the pump is properly grounded. Referto Grounding, page 8 .2. Ensure the High/Low pressure lever is in the

MaintenanceMaintenanceMaintenance ScheduleEstablish a preventive maintenance schedule,based on the pump’s service history. Scheduledmaintenanceis espe

MaintenanceTorque InstructionsNOTE: All fasteners for the fluid covers, centerdiaphragm joint, and manifolds have a thread-lockingadhesive patch applie

Dimensions and MountingDimensions and MountingKEYAluminumSST Aluminum and SSTA12.7 in (323 mm) 11.8 in (300 mm)H6.2 in (157 mm)B14.4 in (366 mm) 12.9

Performance ChartsPerformance ChartsLow Pressure SettingFluid PressureApproximate Cycles per MinutePSI(MPa, bar)020(0.14, 1.4)40(0.28, 2.8)60(0.41, 4.

Performa n ce ChartsHigh PressureSettingFluid PressureApproximate Cycles per MinutePSI(MPa, bar)040(0.28, 2.8)80(0.55, 5.5)120(0.83, 8.3)160(1.10, 11.

ContentsRelated Manuals ... 2Ordering Information... 3Configuratio

Technical DataTechnical DataUSMetricMaximum fluid working pressure200 psi 1.4 MPa,14.0 barAir pressure operating range20-100 psi 0.14-0.69 MPa, 1.4-6.9

Technical DataSound Power (measured per ISO-9614–2)At 70 psi (0.48 MPa, 4.8 bar) and 50 cpmLow Pressure Setting78 dBaHigh Pressure Setting91 dBaAt 100

Graco Standard Husky Pump WarrantyGraco warrants all equipment referenced in this document which is manufactured by Graco and bearing itsname to be fr

Ordering InformationOrdering InformationTo Find Your Nearest Distributor1. Visit www.graco.com.2. Click on Where to Buy and use the DistributorLocator

Configuration Number MatrixConfigurationNumber MatrixCheck the identification plate (ID) for the 20–digitConfiguration Number of your pump. Use thefollowi

WarningsWarningsThe followingwarnings are for the setup, use, grounding, maintenance, and repair of this equipment. Theexclamation point symbol alerts

WarningsWARNINGEQUIPMENT MISUSE HAZARDMisuse can cause death or serious injury.• Do not operate the unit when fatigued or under the influence of drugs

WarningsWARNINGTOXIC FLUID OR FUMES HAZARDToxic fluids or fumes can cause serious injury or death if splashed in the eyes or on skin,inhaled, or swallo

InstallationInstallationThe Typical Floor Mount Installation, page 12,isonly a guide for selecting and installing systemcomponents. Contact your Graco

Installation•Air and fluid hoses:Use only grounded hoseswith a maximum of 500 ft (150 m) combined hoselength to ensure grounding continuity.•Air compre