OperationRoadLazer™ RoadPak™ Line Striping System- For the Application of Road Marking and Reflective Coatings -- For Professional Use Only -List of M
Setup 10 3A1214BRoadPak Mounting Bracket (24G627) Installation (Option 2)NOTE: Cutting the RoadPak mounting arms and bolting them through the bed to t
Setup3A1214B 114. Install the height adjustment bracket (303) to the RoadPak mounting arms (304) with bolts (312), washers (307), and nuts (315). 5. U
Setup 12 3A1214BWide Orientation1. Bolt brackets (316) to the RoadPak in four locations with bolts (312), washers (307), and nuts (315). It is ideal t
Setup3A1214B 135. Install stow-bracket (302) to height adjustment bracket (303). Locate the bottom of the stow-bracket 21 in. to 25 in. (53cm - 63cm)
Setup 14 3A1214B3. Attach the handle (702) to each end of the slide beam. Press the cotter pin (707) through the handle to hold it in place. Fasten nu
Setup3A1214B 15Hose Routing to Pumps and Tanksti16548a
Setup 16 3A1214BHose Routing1. Pull slide beam out to one side of the vehicle. Pull gun arm out and lower it to make sure the hose bun-dle has been se
Setup3A1214B 175. Install air hose to quick connect fitting on air tank.Electrical Cable Connections1. Connect gun arm cable to the junction box. Fast
Setup 18 3A1214BInstall Front Pointer Instructions1. Locate an area on the vehicle to mount the Road-Pak pointer system that will allow the user to se
Operation3A1214B 19OperationPressure Relief ProcedureRPS 2900 Pump Fluid Pressure Relief1. Set hydraulic valve to OFF position.2. Run engine at half t
Models 2 3A1214BModelsComplete AssembliesRef. Model Number Description1 24G624 1 Pump RoadPak2 24G625 2 Pump RoadPak3 24G626 Single Hitch Mounting Fra
Operation 20 3A1214BAir System Pressure Relief1. Relieve air pressure in air tank by turning air valve to OPEN position.EMERGENCY SHUT OFFTo shut down
Operation3A1214B 213. Check engine oil level. Add SAE 10W-30 (summer) or 5W-20 (winter), if necessary.4. Fill fuel tank. 5. Check hydraulic oil level.
Operation 22 3A1214BStart Engine1. Set POWER ON/OFF on Programmable Skipline Controller to ON.2. Set engine to choke position ON.3. Set throttle to ha
Operation3A1214B 236. When paint comes out of return lines, set hydraulic valve to OFF position.7. Close all dump valves.8. Place return lines into pa
Operation 24 3A1214BFlushing the System1. Perform Pressure Relief Procedure, see page 19.2. Flush the system with compatible solvent. Check the system
Operation3A1214B 2513. Open only spray gun ball valves corresponding to paint pumps or color used. NOTE: Never open both valves on the two-color gun a
Operation 26 3A1214BSecuring Gun Arm for TransportationNOTE: Never transport the RoadLazer while the paint gun ball valves are open, the system is und
Technical Data3A1214B 27Technical DataMaximum Working PressurePaint 2900 psi (200 bar)Hydraulics 1950 psi (134 bar)Glass bead system 75 psi (5 bar)Max
All written and visual data contained in this document reflects the latest product information available at the time of publication. Graco reserves th
Warnings3A1214B 3WarningsThe following warnings are for the setup, use, grounding, maintenance, and repair of this equipment. The exclama-tion point s
Warnings 4 3A1214BEQUIPMENT MISUSE HAZARDMisuse can cause death or serious injury.• Do not operate the unit when fatigued or under the influence of dr
Introduction and General Information3A1214B 5Introduction and General InformationIntroductionThis manual and those listed below provide pre-setup requ
Component Identification 6 3A1214BComponent Identificationti15836aBNCDEFGHJRMZLAHAGAFAEACABAAPSTWXAYKQAJAD
Component Function3A1214B 7Component FunctionAAir Regulator Allows regulation of the bead tank air pressureBBead TankHolds up to 36 gallons of reflect
Setup 8 3A1214BSetupCharge BatteryIf the battery is newly purchased or has not been used for a long time, charge it before you use it. Installing Road
Setup3A1214B 9Filter OrientationAfter mounting and securing the RoadPak to the vehicle, position the filter assemblies as desired. 1. Use a hammer to
Commentaires sur ces manuels