Graco Trabon MX Series-Flo Dividers Manuel d'utilisateur télécharger pdf

DESCRIPTION

Trabon MX Series-Flo

Divider Valves are designed for heavy

service and are ideal for large steel mill systems and similar

applications. For modular version (MXP) having the same output

capacities, see bulletin 10132.

A typical MX Series-Flo

Divider Valve Assembly (to the right)

consists of an inlet section, end section and three to ten valve

sections. The basic divider assembly will serve between three and

twenty lube points.

The MX valve sections, which have built-in outlet check valves,

are available in various output per piston cycle sizes (see

speciﬁcations). Each twin (T) section has 2 outlets, one from each

side of the section. Each single (S) section has 1 outlet on either

side, but one outlet must be plugged to operate properly. For

applications with continuous oil lubrication (Meter-Flo) the built in

outlet check valves may be removed.

FEATURES/ADVANTAGES

Delivers metered amount of lubricant.•

Economical and compact design.•

Lubricant outlets easily added or removed.•

Simple to install on new or existing machines.•

Built-in outlet check valves.•

Hone-ﬁtted metering pistons.•

OPERATION

Operational sequence of an MX Series-Flo

Divider Valve

Assembly is deﬁned as “progressive”. The term progressive

means that each valve section completes its piston stroke,

discharging a measured amount of lubricant to the bearing it

serves before the following valve section operates. As long as

lubricant is supplied under pressure to the inlet section of the

divider assembly, valve sections will continue to operate in a

progressive manner. Divider assemblies always follow a constant

discharge pattern. Whenever lubricant ﬂow ceases, the valving

pistons will stop. When ﬂow resumes it will start again at the

same point in the discharge cycle.

Trabon

MX Series-Flo Dividers

SPECIFICATION

Material Plated Steel

Pressure (max) 3,000 psi (207 bar)

Lubricant Oil or Grease

Max Operating Temperature 200ºF (93ºC)

Max Cycle Rate w/Cycle Pin 60 cycles/min.

MX w/o Cycle Pin 200 cycles/min.

Net Weight:

(Divider Valve Assembly approx.)

3 Section DIvider 21 lbs, 6 oz (9.69 kg)

4 Section Divider 25 lbs, 10 oz (11.62 kg)

5 Section Divider 29 lbs, 14 oz (13.55 kg)

6 Section Divider 34 lbs, 2 oz (15.47 kg)

7 Section Divider 38 lbs, 6 oz (17.40 kg)

8 Section Divider 42 lbs, 12 oz (19.39 kg)

9 Section Divider 47 lbs, 2 oz (21.37 kg)

10 Section Divider 51 lbs, 8 oz (23.26 kg)

Torque:

Tie Rod Nut 23 ft lbs

Enclosure Plug 48 ft lbs

Outlet Port Plug 18 ft lbs

Sizes + *cu.in. cm

25T 0.025 0.409

25S or 50T 0.050 0.819

50S or 100T 0.100 1.639

75T 0.075 1.229

75S or 150S 0.150 2.458

100S 0.200 3.278

125T 0.125 2.048

125S 0.250 4.097

150S 0.300 4.917

+ This number is stamped on each valve section

* This is the volume discharge per outlet after one complete cycle

1 2

Résumé du contenu

Page 1 - MX Series-Flo Dividers

DESCRIPTIONTrabon MX Series-Flo® Divider Valves are designed for heavy service and are ideal for large steel mill systems and similar applications. F

Page 2 - Contact us today!

DIMENSIONS Inches/(mm)ORDERING INFORMATIONNOTES:1. Capacity sections are speciﬁed starting from inlet section, and must equal number of sections spec

Commentaires sur ces manuels

Pas de commentaire

Graco Trabon MX Series-Flo Dividers Manuel d'utilisateur

Naviguer en ligne ou télécharger Manuel d'utilisateur pour Non Graco Trabon MX Series-Flo Dividers. Graco Trabon MX Series-Flo Dividers User's Manual [en] Manuel d'utilisatio

Résumé du contenu

Commentaires sur ces manuels

Produits connexes et manuels pour Non Graco Trabon MX Series-Flo Dividers