Graco 3A0735J Manuel d'utilisateur

Instructions and PartsSaniForce™ 12:1 Sanitary PumpsFor use in sanitary applications to transfer medium to high viscosity fluids. For professional use

Troubleshooting 10 3A0735JTroubleshooting1. Follow Pressure Relief Procedure, page 8. 2. Check all possible remedies in the Troubleshooting Chart befo

Service3A0735J 11ServiceDisconnect the Pump1. Remove the pump from the fluid container. Operate it at a slow rate to pump out as much fluid as possi-b

Service 12 3A0735J7. Hold the piston rod (106) with a wrench. Use another wrench to loosen the intake valve housing (115), then remove it. If the inta

Service3A0735J 13Reassemble the PumpNOTE: Any damaged rubber parts must be replaced as they could harbor microorganisms that can contaminate the fluid

Service 14 3A0735JReconnect the Pump1. Ram-mounted pumps: Set the displacement pump in place, then attach the clamp. Align the air motor and set it on

Service3A0735J 15

Parts 16 3A0735JParts12345678101091213141516181920Apply PTFE tape to threads.1Hand tighten only.2Apply sanitary lubricant.320ti16013a21a21b2223Complet

Parts3A0735J 17Complete Pump Models 24F625 and 24F626▲ Replacement Danger and Warning labels, tags, and cards are available at no cost.KitsMuffler Kit

Parts 18 3A0735JDisplacement Pump Models 24G761 and 24G762101102115116*117103b*103c*103a103d*104105106108*109107*110112113118118123*121120119122114110

Parts3A0735J 19Displacement Pump Models 24G761 and 24G762* Parts included in Repair Kit 24G555 (Displacement Pump Model 24G761) or Repair Kit 24G556 (

Models 2 3A0735JContentsModels . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2Warnings . . . . . . . . . . . . . . . . . .

Parts 20 3A0735J

Dimensions3A0735J 21Dimensionsti15718a47.5 in(121 cm)*21.1 in.(54 cm)*16.1 in.(41 cm)*4.1 in.(10.4 cm)* Add 4.7 in. (12 cm) to allow for full extensio

Performance Chart 22 3A0735JPerformance ChartCycles per MinuteFluid Flow gpm (lpm) tested in No. 10 weight oilFluid Outlet Pressure psi (MPa, bar)Air

Technical Data3A0735J 23Technical Data* Sound power at 70 psi (0.48 MPa, 4.8 bar), 20 cpm. Sound power measured per ISO-9614-2.** Sound pressure was t

All written and visual data contained in this document reflects the latest product information available at the time of publication. Graco reserves th

Models3A0735J 3Material Certification Reference: SaniForce Product FamilyIssue Date: September 14, 2011 All fluid contact materials in the SaniForce

Warnings 4 3A0735JWarningsThe following warnings are for the setup, use, grounding, maintenance, and repair of this equipment. The exclama-tion point

Warnings3A0735J 5EQUIPMENT MISUSE HAZARDMisuse can cause death or serious injury.• Do not operate the unit when fatigued or under the influence of dru

Installation 6 3A0735JInstallationGroundingPump: Connect a ground wire (Graco PN 238909) to the ground screw on the bottom cover of the air motor, und

Installation3A0735J 7Install a pump runaway valve (S) in the pump air line to shut off air to the air motor automatically if the pump starts to run to

Operation 8 3A0735JOperationPressure Relief Procedure1. Shut off the air supply to the pump.2. Close the bleed-type master air valve (required in syst

Maintenance3A0735J 9MaintenanceFlushing ProcedureNOTE: • Flush before fluid can dry in the equipment, at the end of the day, before storing, and befor